TRW-Repairman

About Ameren Missouri

Ameren Missouri has been providing electric and gas service for more than 100 years, and our electric rates are among the lowest in the nation. Ameren Missouri's mission is to power the quality of life for our 1.2 million electric and 132,000 natural gas customers in central and eastern Missouri. Our service area covers 64 counties and more than 500 communities including the greater St. Louis area

ORGANIZATION UNIT: Power Operations, Power Plants

APPLICABLE TO: Fossil Fuel Plants

DUTIES:

Under direct, indirect, or intermittent supervision, and working on a rotating shift schedule or day

schedule as required, to do a general range of electric arc and gas welding and cutting, brazing,

pipefitting and insulation installation and/or removal on all varieties of power plant equipment.

Immediate responsibility at times for the working direction of an apprentice. Work includes a

general range of electric and gas welding on power plant equipment including structural steel

erection and piping where certification is not required. In addition, to perform other

maintenance work on heavy mechanical equipment, such as replacement of liner plates in fans,

coal chutes and hoppers; welding repairs to castings and equipment; fitting and welding of all

sizes of piping and valves, including items such as measuring, laying out, cutting, threading,

bending, fitting and installation of pipe and tubing, replacement of flange, valve, and heater

gaskets; valve repacking, repair and overhaul; cleaning and replacement of condenser and heat

exchanger tubes; where applicable, repair of traveling water screens. Refractory and insulation

work includes items such as but not limited to furnace wall insulation and protective covering;

insulation coverings on furnace wall fire side linings, slag tanks and hoppers; gas and hot air

ducts and breeching; precipitator casings, main, reheat, and extraction steam lines; boiler feed

piping; steam and condensate drains; feedwater heaters and storage tanks; turbine casings,

steam chests and valves. In connection with this work:

Take welder qualification tests as required.

Work from drawings and sketches.

Check (including Workman’s Protection Assurance where appropriate) to insure

that equipment to be worked on has been properly isolated and protected.

Obtain required materials from storeroom.

Set up rigging and operate lifting equipment.

Erect and work from scaffolds.

Operate and/or use mobile equipment, shop equipment, portable power tools,

other portable tools, hand tools and test equipment as required to accomplish

assigned jobs.

Prepare reports of work done accompanied by sketches, if necessary; complete

such forms as may be required.

Repairman (continued)

3252 - Repairman 8/11/85

3352 - PPM Repairman Page 2 of 3

3354 - Plant / PPM Repairman Apprentice

Work alone or in combination with other Repairman (Certified) or Repairman

classifications when assigned.

Do similar and less skilled work as required.

SPECIAL RESPONSIBILITIES:

For carrying out prescribed safety precautions and safeguards for the protection of himself and

others.

When necessary, check for explosive gases before operating torches.

For observing and insuring that those temporarily under his direction observe safety instructions

issued or applicable.

For performing work without disturbing other equipment.

For executing orders quickly and properly.

For accuracy of work within required tolerances or specifications.

For special care and watchfulness to avoid errors in the repair and assembly of equipment.

For proper use and care of a wide variety of tools, material, and equipment.

For disposition of surplus and scrap materials after each job and keeping areas where work is

performed clean and orderly to maintain an atmosphere conducive to good work practices and

safety.

CONTACTS:

With Plant Operations, Maintenance, and Storeroom supervision and personnel.

WORKING CONDITIONS:

Full range of temperatures from very hot to sub-freezing. Sometimes sudden changes from one

extreme to the other. Subject to noise, dusts, dirt, fumes, odors, drafts, and inclement weather.

Work at times in cramped and artificial light is frequently necessary.

HAZARDS:

Subject to hazards existing from possible failure of nearby equipment; to danger from falling

while working at elevations above grade, to burns from hot metal, piping or slag; to eye injury

from arc flashes; or from any relaxation of the constant care to observe all required safety rules;

and to the usual hazards encountered in mechanical construction and maintenance work.

Occasionally exposed to noxious fumes in confined places.

Repairman (continued)

3251 - Certified Repairman 8/11/85

3351 - PPM Certified Repairman Page 3 of 3

3353 - Plant / PPM Certified Repairman Apprentice

QUALIFICATIONS:

Qualification standards as established in the Apprenticeship Program. In event no graduating

apprentice is available:

Must satisfy requirements as prescribed in the Supplementary Agreement on Uniform

Practices Regarding Promotion to Repairman Jobs.

Must be accurate, steady and calm in emergencies; possess normal physical strength and

endurance; and have no color deficiency in vision.

Hourly Pay:

Grade Step OA 048 Step 1 of 1 (Top Step) - 50.89 USD

Position is eligible for annual incentive payments based on company performance and subject to sole management discretion. Visit our Benefits & Perks Page for more information on benefits provided to regular full-time employees.

If end date is listed, the posting will come down at 12:00 am on that date:

Monday May 19, 2025

All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, national origin, ethnicity, age, disability, genetic information, military service or status, pregnancy, marital status, sexual orientation, gender identity or expression, or any other class, trait, or status protected by law.